Stainless Supply | Stainless Steel Backsplashes
HAVE YOUR OWN DRAWING?

If you have a drawing that you would like us to see, then upload it here.

Select "Yes" then click the "Browse" button to find your drawing on your computer.

Once you've browsed for your drawing, click the "Submit" button to upload it to our servers.

Make sure the file is no larger than 5MB and should be one of these file formats: .jpg, .gif, .png, .pdf, .dwg, .dwf, .dxf, .sldrw, .igs, .step, .stp, skp, .dae.

SELECT YOUR METAL/FINISH

You can choose either a Brushed (#4 Polish) finish or a Mirrored (#8 Non-directional) finish.

The #4 finish is most commonly seen on kitchen appliances.
The #8 finish has absolutely no grain and looks just like a mirror.

Choose any of the following:

  • 304 #4 (Brushed) - will NOT hold a magnet
  • 304 #8 (Mirror) - will NOT hold a magnet
  • 316L #4 (Brushed) - will NOT hold a magnet
  • 316L #8 (Mirror) - will NOT hold a magnet
  • 430 #4 (Brushed) - will hold a magnet
  • 430 #8 (Mirror) - will hold a magnet

Note: Random Swirl Finish comes in 304 and 316L

SELECT YOUR EMBOSSED TYPE

You can choose either the Fine Line or Beveled embossed type.

SELECT METAL THICKNESS

Stainless:
    Light Duty is 24 gauge (.0235")
    Medium Duty is 22 gauge (.0293")
    Heavy Duty is 20 gauge (.0355")

SELECT YOUR PATTERN

Select any of the patterns below.

SELECT YOUR SIZE

Stock Size:

Select one of our pre-cut sizes.
If you choose to add the hemming option, these measurements account for the hemmed edges.

Custom Size:

Enter your own height and length.
If you choose to add the hemming option, the measurement you enter will account for the hemmed edges.

GRAIN PREFERENCE

No Preference - Selecting this will have the grain run either vertically or horizontally.

Yes - Selecting this will have the grain run horizontally along the length. An additiona 10% charge will be added for that particular piece.

Note: If the length of the item is over 47", the direction of the grain will run length of the cut.

CUSTOMIZE SIZE

This is where you can upload a file.

SELECT EDGE/BACKING OPTION

Backer Information:

  • Backer board thickness: 3/8"
  • All backer board edges will be covered by the metal

Hemming Information:

  • Hemming is a fabrication option used to keep the outside edges of the sheet from being sharp.
  • The hems will give the edges a finished appearance.
  • The hems will add a degree of rigidity to the backsplash.
  • When you enter the size dimensions of the piece, that will be the "finished" size. We will compensate the extra material for the hem.
  • Hemmed edges are not sharp, they can be touched with the bare hand with very little to no risk of being cut.
  • The hemming is approximately 1/8" thick around the edges, leaving 1/16" space in the back of the backsplash.
  • The hemming option is for all four sides.

HEMMED EDGE:
304 Stainless, 24 Gauge #4 Polish Finish with hemmed edges.

HEMMED EDGE (BACK):
304 Stainless, 24 Gauge #4 Polish Finish with hemmed edges looking at the back.

REGULAR CUT EDGE:
304 Stainless, 24 Gauge #4 Polish Finish with regular cut edging.

SELECT MOUNTING OPTION

Select your preferred mounting option:

  • None - no mounting options included
  • Holes - 1/8" holes located about 3/4" in from each corner
    (mounting "decorative" screws are NOT included with holes)
  • Tape - double-sided tape to help hold backsplash in place while construction adhesive sets.
    Not recommended without hem, as tape will cause backsplash to sit off the wall
    (construction adhesive is NOT included)

SELECT SHELF OPTION

Select a shelf option:

Selecting the shelf option requires that you select the 'Backer' Edge/Backing Option and Heavy Duty 20G thickness.

  • 6" deep stainless vented shelf
  • Made from the same heavy duty 20 gauge stainless steel
  • Comes with two brackets for easy 'snap-on' installation

ENTER A QUANTITY

Enter the total number of backsplashes of this size/type needed.

You will see the Weight and Price "per piece", as well as the "total" Weight and Price.

Your Account  | 
Login
Stainless Supply

Experts Available
(877) 484-0088
Stainless Supply

SHOP ALL

INSTALL VIDEOS

Design Your Stainless Backsplash In 6 Easy Steps

  • Follow the steps below to design and order your backsplash
  • Relax and wait for your backsplash to arrive at your door!
  • Remember: we are here to help!

Select Your Pattern

- Close
No Pattern
Diamond 3"
Diamond 4"
Diamond 6"
Diamond 12"
Diamond 4" x 8"
Hopscotch
Diamond & Square
Square Grid
Subway Tile
Herringbone
Basket Traditional
Basket Double
Basket Single
Dia 4" Two Tone
Dia 6" Two Tone
Dia 4x8 Two Tone
Square Grid 4"
Random Swirl
 No Pattern
 Diamond 3"
 Diamond 4"
 Diamond 6"
 Diamond 12"
 Diamond 3" x 6"
 Diamond 4" x 8"
 Hopscotch
 Dia. & Square
 Square Grid
 Subway Tile
 Herringbone
 Basket Traditional
 Basket Double
 Basket Single
 Dia 4" Two Tone
 Dia 6" Two Tone
 Dia 4x8 Two Tone
 Square Grid 4"
 Random Swirl
NO PATTERN
DIAMOND 3"
DIAMOND 4"
DIAMOND 6"
DIAMOND 12"
DIAMOND 3"x6"
DIAMOND 4"x8"
HOPSCOTCH
DIAMOND & SQUARE
SQUARE GRID
SUBWAY TILE
HERRINGBONE
BASKET TRADITIONAL
BASKET DOUBLE
BASKET SINGLE
DIAMOND 4" TWO TONE
DIAMOND 6" TWO TONE
DIAMOND 4"x8" TWO TONE
SQUARE GRID TWO TONE
RANDOM SWIRL
Light Duty (24G/.0235")
Medium Duty (22G/.0293")
Heavy Duty (20G/.0355")